Go Back to Maintenance Schedules
| Job | Notes | Part | Quantity |
|---|---|---|---|
| Change engine oil | 10W40 Deutz Engine Oil | 79036470B | 18L |
| Change engine oil filter | O-Ring in the box should be white. | ACO F716200510020 | 1 |
| Oil drain plug gasket | M18x24 | ACO F731200510060 | 1 |
| Change fuel filter | ACO F731200060020 | 1 | |
| Drain water from fuel pre-filter | As required. | ||
| Change fuel pre-filter | ACO F842201060010 | 1 | |
| Change the DEF filter | 1 | ||
| Check air filter maintenance code | |||
| Check engine air intake system for leaks | |||
| Change engine air primary filter | ACO H737200092100 | 1 | |
| Change engine air secondary filter | ACO H737200092110 | 1 | |
| Check and clean cooling radiators and fan | As required. | ||
| Check engine coolant level | Premixed FleetGuard Antifreeze | ||
| Check for coolant system leaks | |||
| Check water pump bearings & leaks at weep hole | |||
| Check fan bearings | |||
| Remove belts, check idler, tensioner bearings + belts |
| Job | Notes | Part | Quantity |
|---|---|---|---|
| Check fluid level for clutch/brake actuation | 72313538 Pentosin Fluid | ||
| Change transmission oil | 821XL Hyd. / Trany Fluid | 79035451B | 47L |
| Change drain plug gaskets | Brake and transmission. | ACO X540009478000 | 2 |
| ACO X540010278000 | 1 | ||
| Change transmission pressure filter and o-ring | O-Ring is 72313495 | ACO F91610060001A | 1 |
| Change transmission suction filter and o-ring | O-Ring is 72424095 | ACO F916100490010 | 1 |
| Check oil level in rear axle final drives | 85W-140 Gear Oil. Fill up to 55mm (2.16") below filler hole. 714 – 716 only | ||
| Check for brake drag with rolling stop test |
| Job | Notes | Part | Quantity |
|---|---|---|---|
| Check oil level in front PTO | 821XL Hyd./Trany Fluid | ||
| Change front axle differential oil | 80W-90 Gear Oil. 714 to 716 use 9L. | 742508 | 2 |
| 79036959B | 9L | ||
| ACO X540007678000 | 2 | ||
| Change oil in front axle hubs | 80W90 Gear Oil | 79036959B | 5L |
| ACO X540009678000 | 2 | ||
| Check front axle toe-in | 0-2mm (0.0 to 0.08") |
| Job | Notes | Part | Quantity |
|---|---|---|---|
| Change hydraulic oil | 821XL Hyd./Trany Fluid | 79037113B | 79L |
| Drain plug o-ring | ACO X548842900000 | 1 | |
| Change hydraulic return line filter | ACO G835860061040 | 1 | |
| Change hydraulic vent filter | ACO F835860061020 | 1 | |
| Change control pressure fine filter | ACO F737960020060 | 1 | |
| Drain oil from couplers' oil recovery bottles |
| Job | Notes | Part | Quantity |
|---|---|---|---|
| Change fresh air filter | ACO H737812140010 | 1 | |
| Change recirculating air filter | ACO H737812140050 | 2 | |
| Clean the a/c condenser | |||
| Check and Adjust A/C compressor belt | |||
| Windshield washer reservoir | Refill as needed. | 15-204 | 1 |
| Job | Notes | Part | Quantity |
|---|---|---|---|
| Operate tank drain valve | Operate drain valve to drain water. | ||
| Check airline antifreeze level | 79019149 | ||
| Compressed air function/leak test |
| Job | Notes | Part | Quantity |
|---|---|---|---|
| Check lighting, signaling, and warnings systems for correct operation | |||
| Check software version, and update if necessary | |||
| Check battery acid level | |||
| Read out, record diagnostic memory & remedy faults |
| Job | Notes | Part | Quantity |
|---|---|---|---|
| Tighten wheel hardware to specifications | Torque specs listed below. | ||
| Check for loose hardware, linkages; check for leaks | |||
| Check tire pressure | |||
| Lubricate all grease points | 79014728B | 1 | |
| Brake Clean for cleanup | 890.9107 | 1 | |
| Test drive tractor, checking functions & braking systems | |||
| Check brake control | |||
| Check electro-hydraulic steering |
| Job | Notes | Part | Quantity |
|---|---|---|---|
| Front wheel center to hub | 330 ft/lbs (450NM) | ||
| Rear wheel center to hub | 430 ft/lbs (580NM) | ||
| Front wheel rim to dish | 207 ft/lbs (280NM) | ||
| Rear wheel hub tapers to axle (3 step tightening) | 340 ft/lbs (459NM) | ||
| Rear wheel rim to dish | 206 ft/lbs (280NM) | ||
| Wheel Weight, Rear/Tapered Cones – (M16 Bolt) Torque Spec | 195 ft/lbs. with M16 Bolts |
Contact Us Regarding Stock: